Installation Instructions for Ford Focus Tools & Materials Needed: 1. Utility Knife 2. Wire Crimper 3. Torx™ Wrenches 4. Hex Nut Drivers 5. Drill and Bits 6. Phillips Head Screw Driver 7. Crank Spring Removal Tool (Special Tool, available at most Auto Parts Stores) – or – 8. Flat Screw Drivers (2) 9. Add-A-Circuit™ fuse adapter 10. Silicon Sealant (Clear or Black) Procedure: (Approximate time to complete installation: 3 - 4 hours) A. Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back.
Read the rest of this entry »

• 0 Comments

Ford Focus Dead Pedal Installation Guide following step: Step 1 - Gather required tools. Please gather the following tools before you begin the installation: * Power Drill. * 3/16 drill bit. * Large flat head screw driver. * Large Phillips head screw driver. * Sharp utility knife or razor blade. * Fine permanent marker. * Center punch & hammer - optional. Step 2 - Unpack Dead Pedal kit and verify contents. Remove all items from the the shipped package. Copyright © 2003 Redline Tuning LLC. All Rights Reserved. You should have the following before beginning: * RedlineTuning Focus Dead Pedal * (2) Washers * (2) Sheet Metal Screws * Printed Installation Instructions Step 3 - Remove trim molding and kick panel. A. Carefully remove the inside door trim molding shown below in Figure 3a. It will snap off. B. Using a flat head screw driver, remove the two plastic screws that hold on the kick panel (lower left below Instrument Cluster).
Read the rest of this entry »

• 0 Comments

Step for this Ford Focus Fuel Door Installation Guide: Step 1 - Gather required tools. Please gather the following tools before you begin the installation: * Power Drill * Utility Knife. * 3/16 drill bit. * Duct Tape * 9mm or 11/32 open ended wrench. * Pliers. * 9/64″ Hex Key or Allen Head wrench * Small piece of cloth. * Flat file for filing metal. * Zip tie - medium size. * Rasp file or round file. * Body color touch up paint. * Fine permanent marker. * Phillips screw driver. Step 2 - Unpack fuel door kit and verify contents. Check items you removed from the box.
Read the rest of this entry »

• 0 Comments

This Ford Oval Owners Manual manual is 100 years in the making, so pay attention, and learn the best way to showcase and represent one of the most powerful and valuable symbols in the world. Why is this manual important? The Ford Oval proudly represents the Ford brand and is widely recognized by consumers around the world. As such, it is reproduced thousands of times everyday. Without clear guidelines, it would be too easy for it to be inaccurately reproduced, which would result in too many variations to the standard, which in turn would result in inconsistent messages to our customers. Your role in ensuring that the Ford Oval continues to represent all that is great about the Ford brand is vital.
Read the rest of this entry »

• 0 Comments

This Ford Oval Owners Manual manual is 100 years in the making, so pay attention, and learn the best way to showcase and represent one of the most powerful and valuable symbols in the world. Why is this manual important? The Ford Oval proudly represents the Ford brand and is widely recognized by consumers around the world. As such, it is reproduced thousands of times everyday. Without clear guidelines, it would be too easy for it to be inaccurately reproduced, which would result in too many variations to the standard, which in turn would result in inconsistent messages to our customers. Your role in ensuring that the Ford Oval continues to represent all that is great about the Ford brand is vital.
Read the rest of this entry »

• 0 Comments

ntroduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo with single CD AM/FM stereo with in-dash six CD Climate Controls Heater only Manual heating and air conditioning Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Remote audio controls Locks and Security Keys Locks Anti-theft system Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Tire Inflation Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Traction control Transmission operation Roadside Emergencies Getting roadside assistance Hazard Read the rest of this entry »

• 0 Comments

Before starting, be sure the vehicle has 91 or better octane fuel in it. DO NOT try to run the vehicle at full throttle at sea level altitude with a supercharger unless the fuel tank is filled with good 91-octane fuel. Failure to heed this warning can result in severe engine damage. Special Note: If you do not have a factory workshop manual, buy one now! It is good to have for any repairs now and in the future.
Read the rest of this entry »

• 0 Comments

The Group B RS200 rally car is now enjoying a second career as an enthusiast s track day machine Think of the most stirring motoring moments you ve ever witnessed and there ll almost certainly be a Group B episode or two in there.Group B left an impression like no other branch of motor The problem was,it left too big an impression for all the wrong reasons: deaths were an integral part,so it was no surprise when the series was canned before many of the key cars had even been fully developed. One example was the RS200,set to crush its rivals only to have the plug pulled before it had even got going. The RS200 project started in 1983;Ford needed to get a competitive rally car developed and built as quickly as It would have four-wheel drive, and a unique shape so it wouldn t immediately be obsolete.
Read the rest of this entry »

• 0 Comments