This guide will show you how to fit ‘Citroën/Peugeot Windscreen Washer Mist Jets’ into your Fiat Bravo. Please read this guide through at least once before fitting. Your first step is to purchase the ‘Citroën/Peugeot Mist Washer Jets’ from the dealership. Part number 6438.V8. They come as a pair for approximately £6.
Read the rest of this entry »

• 0 Comments

First of all we need to obtain the Fiat Marea rear door handles, once obtained we can now begin to fit them to the Fiat Bravo. Below are two examples of a Fiat Marea rear door handle and the Fiat Marea/Bravo front door handle.
FIAT MAREA/BRAVO FRONT DOOR HANDLE - Circled in the photograph is the rear mounting point for the bolt required to fit these handles to the front door.
Read the rest of this entry »

• 0 Comments

OK, first the banging and force pulling method is OUT !!!! All of the Bravo/a seat head rests can be removed whit ease. You only need these pliers (don’t know the right name ;) ) The next step is to pull up the head rest and grip the pins whit these pliers.
WARNING : Put some thick cloth under them plieers, or the plastic will get “eaten“ !
Read the rest of this entry »

• 0 Comments

This guide will show you how to renew your old existing Bonnet Pin and Lock. Please read this guide through at least once before fitting.
Step 1. (Optional) Preparation prior to fitting
Before you start removing your old parts you may want to consider preventing your new parts from corroding like the existing ones. You could smear a protective oil or grease over the exposed metal and rub it over or you could like myself spray paint the metal parts.
Read the rest of this entry »

• 0 Comments

The first step is to locate the MAF sensor. Its position is on the air intake system, after the air filter box.
The second step is to unplug the connector on the MAF sensor. It has a clip that holds it firmly in place, so you need to push the clip with your finger to release it. (red arrow) Then just pull the plug off.
The third step is to unscrew the two torx security screws. To do that, you will need a trox screwdriver T20. After the screws are out, gently pull the sensor out of his casing.
Read the rest of this entry »

• 0 Comments

The first step is to remove the old (bravo) console. You do it like so. First remove the clips and screws near the front end of the console on its sides (circled red) Then remove the rubber in the “shelf“ of the bravo console using a knife or a small screwdriver and lift it up. Unscrew the screw underneath it. Lift the gear stick gator like in the pic above and use force to get the gear knob off – grip the gear knob with your hands and pull in the direction of the arrow (upwards)
Read the rest of this entry »

• 0 Comments

This guide will show you how to fit ‘Citroën/Peugeot Windscreen Washer Mist Jets’ into your Fiat Bravo. Please read this guide through at least once before fitting.

Your first step is to purchase the ‘Citroën/Peugeot Mist Washer Jets’ from the dealership. Part number 6438.V8. They come as a pair for approximately £6.
Read the rest of this entry »

• 0 Comments

Your first step is to buy a pair of Fiat Marea Poly Elliptical Headlights which can be found on all Fiat Marea ELX and HLX’s of any age. Your second step is to make sure that you are also given the sidelight connector with part of the wiring loom; it isn’t entirely necessary to obtain this but it does make it a lot easier to install and look factory fit. Make sure you have enough of the wiring loom as possible as you will be wiring them into the Bravo’s wiring loom. (Approx 30cm).

You can extend the wire using good quality speaker wire, so don’t worry if it’s too short. The rest of the headlight connectors on the Bravo will fit directly into the new Marea Headlights. (These are the Indicator connector, Dipped/Main Light Connector).

Bravo Headlight Removal
Pre-Removal
If you have bought used headlights, theoretically they will already be aligned for you. Therefore if you want to save yourself time and money by not having your lights realigned then mark off the position of the brackets and bolts in there current position before removal. If possible mark the headlight pattern on a garage door or wall.

I would still recommend you get them aligned properly just to be on the safe side as well as make sure you don’t loose valuable light. Approx £12

Download pdf Fiat Marea Poly Elliptical Headlight Conversion PDF

• 0 Comments